TargetTalk

[quote="Mark Briggs"]This is a common problem with Pardini electronics. I discovered the fix is far more simple than most people believe. The issue is that the electronic block is held in place with only two screws and these screws "shoot loose". Mark, thank you for the valuable ...

My Pardini SP1 started to do the same thing after coming back from the gunsmith - on rapid fire just a selenoid click. I drop the clip and pull the bolt back about 1/4", just enough to ensure the bullet is chambered properly. After 6 or 7 selenoid clcks, the gun with go off. I told North Sylva ...

Yes, I called the CFO this morning and got a temp ATT. Thanks.

I found the black dry-fire plug. I can lift the sear from the selenoid and the hammer releases but if I pull the trigger it just clicks away. I have tried different (new) batteries. I got an ATT and will take it to Peter tomorrow. Thanks.

I seem to have misplaced the little blue plug. I put in the blank plug from my Walther SSP ant it works. I can cock the gug with the handle off, lift the plate above the selenoid and the sear releases the hammer. If I slide the handle on, I have to pull the trigger and and 10 - 15 clicks before the ...

Nope. One of the first things I did was changed the batteries. Sorry I forgot to mention that.

{addendum} I am able to what is not happening – the hammer is not releasing. I pulled the handle off and I can where the sear is engaging the hammer but the hammer is not getting released. I slipped the handle back on with the batteries and pulled the trigger about 20 times. I got 20 clicks of the s...

My Pardini is one week old and has about 100 rounds through it. Tonight I shot off 20 goods shots on one target. I changed the target and all I got was a click from the electronic mechanism. I pulled the trigger a few more times and another shot went off randomly. I thought I had a bad round so I ch...

Last night I sprayed a little G96 on the slide and put 100 rounds of CCI standard through. Not one jamb! I'll break it in with my CCI and hope after that my RWS Target Pistol works. I just bought a case of that because it works so well in my Walther SSP.

In the parts breakdown for the SP1 electronic, what is the part number for the buffer mentioned in this thread? I have a new SP1 Electronic with about 100 rounds. It occasinally tries to eject a casing while feeding a new bullet and jambs. Any ideas? I am using RWS Target Pistol. Should I wait until...

I have a Walther SSP I have been shooting for two years. During rapid fire, the trigger does not reset. I literally have to completely remove my finger from touching the trigger and even then, it takes a couple of movements of the durigger (1st stage) before it resets. If I am doing timed or slow fi...

Neoprean cushions on the bottom

Here are a few pictures of my new pistol box based on plans from Dick Flagg. Plywood laminated in birch. Gil H. scope mount, I drawer with glides. Felt lined. Nickel 3/4" lock. The Walther SSP is not included :-) Instead of traditional corner protectors, I used 3/4" x 3/16" aliminum s...

Sorry to ask such 'noobee' questions, but do you use anything on your cloth as you clean around the chamber? I notice wax also builds there.

Thanks,

The pistol is new, less than 200 shots. I am glad to hear it improved for you. Do you have any advice for minor cleaning after shooting? Without breaking the pistol down every 2000 rounds, is there a procedure to clean around the chamber and ejector? Should anything be lubricated, including the slid...

I have an issue and I thought I would throw it out in case anyone else has experienced this. Every once in a while, maybe 10 times so far, the slide will not go all the way forward and I get a misfire. If I open the slide, the bullet is still in the chamber and does not eject. I have to pry it out w...