TargetTalk

Is there any documentation on how to read the hard copy print out from the Suis Ascor system ? For the air pistol event, the print out would look some thing like : 1 -> 9P 45:20.66 10.73/ 3.01 What does "45:20.66" indicates ? I believe "10.73 / 3.01" is some sort of shot position...

Hello Bill, Would appreciate it if you could share with us the address of those chinese shooting web site. Thanks DO NOT BRING AN AIRGUN WITH YOU!!!!!!!!! its classified as a firearm over there I don't think they even allow air soft they have the best olympic team, they are Eley's biggest customer a...

I personally have not encountered any problem using Target Pistol. However, I am still getting a lot of 4, 5's so a flyer due to lousy ammo is not going to be some thing I will notice. However, the other shooters around all seem to think I should be using some other stuff instead, then again, these ...

Is RWS Target Pistol suitable for use as training ammo for Free Pistol ?

The only other "low cost" ammo I can get my hand on is RWS Rifle Match but I find it has a rather severe recoil.

Thank you.

I would like to know how to go about checking the fit of the grip for Air Pistol / Free Pistol. What I was thinking of doing is to : (1) stand facing a blank wall (2) adopt the proper stance (3) raise the pistol into firing position (4) align the sight (5) close my eye for a few seconds (6) check th...

after talking with some of guys around here, the agreement is to file down the grip a bit to give more clearance for the rear sight. Fred is correct about the short Front Sight, one of the SP New in the club has a very short Front Sight and it means center hold was not possible on that gun. It seems...

Greetings, I was shooting a SP New and found the gun shooting too high, with the usual sub six hold, all the shots are going off the top of the target paper ! Adjusting the rear sight did not help much, the rear sight element is already bottom out on the grip. Can the grip itself be modify to lower ...

How does the trigger of the P44 compare to the LP10 ?

Greetings, The barrel / bolt contact pressure can be adjusted by : (1) removing the barrel sleeve / jacket ( the piece that the front sight is attached to ) (2) lossen the two barrel screw (3) close the bolt (4) shift the barrel back towards the rear sight until it made full contact with the bolt (5...

Greetings, At our local range, we have noticed that 2 LP10 was leaking air around the chamber / breech as you have described. This was tracked down to the barrel been set too far forward, we have to move the barrel a bit back to form a tight seal. In the case of the 2 LP10, it appears the two "...

guest122 wrote:
By adjusting the trigger as described above you will get a Toz-35 kind of feeling...but with 500gr...I can live with that, but feel the kick back is very annoying...

What is a "Toz-35 kind of feeling..." ?

http://news.bbc.co.uk/2/hi/health/5326742.stm

the above article in BBC news seem to suggest that looking very hard at the Front sight might actually be counter productive.

Unforunately it did not say what can be done about it though.

Mark and David, thank you for your reply, the information was just what I was looking for. I took a closer look at my Morini today and noticed that the gold contacts on the grip electrionic shows quite a bit of wear. The under lying PCB board can be seem "through" the contacts !! Is this a...

hello,

Does anyone have any information on how to dis-assemble the CM84E ?

I would like to know the basic stuff like changing firing pin / spring etc.

thank you.

Greetings,

took a closer look at the 208 today, it looks like the sear or the hammer is worn out.

Will have to see if the club got any fund to send it in for repair.

thanks everyone for helping out.

As a side note, I was wondering how the circuit board and battery compartment are fitted in the Rink Grip.

I was told the Rink Grip has a "odd extension block" to hold the circuit board and battery.

Thanks

Blue-tac is great for trying things out when modifying the grip. But in the long run, it is better to replace the Blue-tac with something more permanent. The problem is that Blue-tac do shift around a bit and get slightly compact over time. If you do not wish to use the Morini Grip compound, there a...

Once again, let me thank everyone for taking time to help me out. I have taken a closer look at the 208 manual and it seem to me that the trigger weight == sear enagement pressure . If this is true, then my course of action come this weekend would be : (1) de-grease the sear (2) increase the trigger...

Oops, should have RTFM, the manual for the 208 clearly stated that sear enagement is NOT user adjustable ! Anyway, a little background info, I realized of course that such a weapon should be sent to a gunsmith. However, due to local reg and other issues beyond my control, that is not going to happen...

Is there anyway to increase the sear enagement on a early model Hammerli 208 ( S/no 206** ) ? From the 10P Files, it seem like the only adjustment available is the trigger weight. I would like to increase the sear enagement because the pistol have a tendancy to go "full auto" when the slid...