TargetTalk

The cylinders work on 200 Bar.

Hi Jim I have just measured my MGH1 adaptor the OD of the thread and pitch seems to fit more to imperial sizes and thread pitch so here are my measurements imperial .900 OD of an inch and 14 threads per inch Metric 22.84 OD and 1.75 TPI but 14tpi is a better fit when checked with thread gauges The t...

One way to put some heat on just the screw and on a very local area is to use a soldering iron with no solder.

robjob wrote: ↑Sun Jan 17, 2021 10:22 am Walther lp400/500 and Hammerli ap20 are the same mount.

Hammerli are owned by Walther I believe so that could be the reason both makes use the same cylinder mounting.

I have used milliput which is an epoxy putty which is highly adhesive to most materials and drys hard. When its soft you can fix it to the grip and then grip it to get it to the rough shape and then you can file or grind it with a dremel to get an exact fit.

Hang in ther keep doing the training drills and when your scores start to improve the smiles will return but you have to put the hard yards in to reap the rewards.

I have just looked on the Gehmann website and the New Gehmann air pistol is from what i can see a rebadged MG1, i shoot a MGH1 and all the sales words readjustments ectara are the same as the MG1 /MGH1. It will be interesting to see how long it is before Gehmann are offering the equivalent MGH1. Hav...

I have just looked on the Gehmann website and the New Gehmann air pistol is from what i can see a rebadged MG1, i shoot a MGH1 and all the sales words readjustments ectara are the same as the MG1 /MGH1. It will be interesting to see how long it is before Gehmann are offering the equivalent MGH1. Hav...

I have an MGH1 and I have found the velocity changing on it own. I set the velocity to 535 fps and it was very consistent over 15 shots it varied just 2 fps but two weeks later it sounded soft when I shot it. After checking the speed again, I found it was recording 467 fps when adjusting the part to...

Its not the sear ajustment thats needs to be reset as per the instructions in the handbook.

Can i ask what is firelaping?

I have a MGH1 where you can adjust the depth of the rear sight notch what depth is best a deep one or shallow one.

Its interesting that she is also using the trigger shoe that was on the LP1 air pistol which has only back and forward ajustment.

Please do not use this link http://www.variolens.de/english.html as it is for Surrey Guns here in England and they went bust in a big way about two years ago. So don't go sending any money to this link.

I Think its also for FWB 65,80 or 90 for the 100 series did they not have another piece of wood that fitted to the top of the grip and which went across the top of your hand between the thumb and first finger.

I just used a sharp craft knife to cut the filler, before cutting I did wet the knife.

I had this problem with my P34 I got over it by applying the filler to the finger grooves and when I had the grip how I wanted it I cut down through the filler down the join in the grip. After doing the cut I removed the grip halves until the filler had hardened then I reassembled the grip.

So all you need is a vice like grip.

Ok. you asked for it..... Qiang Yuan Qlympic pellets from China. They are 4.49 mm diameter and 0.53 g per pellet . packed on seperate 200 pcs. sheets. Minimum order is 10'000 pcs. But you need to get the special ones made for there Olympic team only that are 4.493 mm diameter and have been sorted b...

I have a Match gun MGH1 the electronic trigger works very well but the mechanical trigger can only be adjusted down to a weight of 700gms. When I queried it with Match Guns they replied that the mechanical trigger is only there for emergency use if the battery runs out during a match. looking at the...