Page 1 of 1

FWB P44 probe 0-ring

Posted: Mon Oct 14, 2024 8:53 am
by KDZ
I got the impression that my P44 was shooting inconsistently* so checked it with a chronometer. Two 10-shot strings using 7gr RWS basic pellets:

Mean 328fps 325fps
ES 40 57
SD 17 17

FWB documentation indicates factory velocity of 150 M/s, which is 492 fps: The gun is shooting very slow, about 65% of nominal

Borrowing a test from air rifle, I shot the pistol with a 1" patch of paper towel sitting over the chamber where the probe inserts. Sure enough the patch goes flying, indicating an air leak between the probe and the chamber.

The manual calls for 4mm X 1mm o-ring on the probe so I ordered some. Anything else I should look at?

Thanks

*Couldn't be me, right?

Re: FWB P44 probe 0-ring

Posted: Mon Oct 14, 2024 1:44 pm
by David M
Little bit of lube when you put the new O ring on.

Re: FWB P44 probe 0-ring

Posted: Tue Oct 15, 2024 6:23 am
by deadeyedick
Silicone grease only as lube.

Re: FWB P44 probe 0-ring

Posted: Tue Oct 15, 2024 8:24 am
by Gwhite
Silicon is great for O-rings, but not much else. Get a small tube of SuperLube synthetic grease, which works just as well on O-rings, and can also be used on things like cylinder threads.

https://www.amazon.com/Super-Lube-21010 ... B005R2NIIC

Re: FWB P44 probe 0-ring

Posted: Tue Oct 15, 2024 9:02 am
by KDZ
Thanks guys will do

Re: FWB P44 probe 0-ring

Posted: Tue Oct 15, 2024 12:17 pm
by David M
My favorite is Festo Pneumatic assembly grease.
ef0a0ac1ecb644b58de784a4df719462.jpg
ef0a0ac1ecb644b58de784a4df719462.jpg (18.63 KiB) Viewed 1558 times

Re: FWB P44 probe 0-ring

Posted: Thu Oct 17, 2024 12:08 pm
by KDZ
So the O-ring from Amazon isn't correct - much smaller than the one on the probe. FWB P44 exploded diagram indicates "O Ring 4.0 x 1.0 – 4.9.0001".

This is the undersize Amazon O : https://www.amazon.com/dp/B09CL3VZ6L?re ... title&th=1

Does someone know which O-ring to get?

Thanks

kz

Re: FWB P44 probe 0-ring

Posted: Thu Oct 17, 2024 12:33 pm
by Pistoley
This is the genuine one, but shipping is more than the seal so I would order several or other stuff to make it worthwhile.

https://www.ebay.ca/itm/374825198999?_s ... R7q7urjTZA

Re: FWB P44 probe 0-ring

Posted: Thu Oct 17, 2024 1:10 pm
by KDZ
Thanks! I ordered two

Re: FWB P44 probe 0-ring

Posted: Thu Oct 17, 2024 2:32 pm
by Gwhite
KDZ wrote: Thu Oct 17, 2024 12:08 pm So the O-ring from Amazon isn't correct - much smaller than the one on the probe. FWB P44 exploded diagram indicates "O Ring 4.0 x 1.0 – 4.9.0001".

This is the undersize Amazon O : https://www.amazon.com/dp/B09CL3VZ6L?re ... title&th=1

Does someone know which O-ring to get?
Metric O-rings are usually specified by the internal diameter & cross-section. The FWB spec follows that convention. The O-rings from Amazon have a 4 mm outside diameter.

Re: FWB P44 probe 0-ring

Posted: Fri Oct 18, 2024 1:00 am
by Azmodan

Re: FWB P44 probe 0-ring

Posted: Fri Oct 18, 2024 6:34 am
by Dmaryakh
Figure out which seal you need here - https://www.feinwerkbau.de/en/service/d ... ftpistolen

Then can order just a seal or entire seal kit from SportShootingDepot (FWB dealer) - http://sportshootingdepot.com