K38 or AKA Model 14-4 question

If you wish to make a donation to this forum's operation , it would be greatly appreciated.
https://www.paypal.com/paypalme/targettalk?yours=true

Moderators: pilkguns, m1963, David Levene, Spencer, Richard H

Forum rules
If you wish to make a donation to this forum's operation , it would be greatly appreciated.
https://www.paypal.com/paypalme/targettalk?yours=true
Post Reply
Tom Suswal
Posts: 10
Joined: Fri Jan 14, 2005 10:09 am

K38 or AKA Model 14-4 question

Post by Tom Suswal »

I have a M-14-4 Target Master with the target sights, hammer and triger. I have been useing it for fun and mostly with a 6 o'clock hold. I have been thinking about also useing it for CF in USAS matches. My problem is that when I try to shoot center hold at 25m I find that I bottom out the rear sight and still do not have a center group, (high 9's & 8's). It is also very hard to pick up the sights as the rear sight is very small. What would some of you do to solve the above problems? Do any of you know of a replacment rear sight that will give me a better sight picture and the need adjustments to find center hold.

Thanks

Tom S.
Lee Jr
Posts: 51
Joined: Wed Mar 03, 2004 7:09 pm
Location: Columbus, IN

Post by Lee Jr »

Tom, your best alternative would be to add the Weigand rear sight blade: http://www.jackweigand.com/smith_wesson_rear_blade.html
I haven't tried one myself but they look very good and aren't very expensive at all. I originally put a Millet rear sight on mine, which while an improvement over the stock sight I did not feel it had a large enough rear sight blade. I ended up going to an Aristrocrat rib which has a really nice large rear sight blade and also has a 3 position rear sight adjustment that makes switching from a sub-6 hold on the precision target to a center hold on the duel target a snap.
Mike Taylor
Posts: 212
Joined: Mon Mar 01, 2004 4:03 pm
Location: Okanagan Valley, British Columbia

M14 alternative sight

Post by Mike Taylor »

Austin Behlert (gunsmith) made a rear sight for the Model 14 that provided greater downward travel . It is a "drop-in" replacement (at least on my 14-3). I had the same problem as you with the original S&W rear sight. The Behlert sight allows me to use a centre hold. The bad news is that the sight is no longer made and so you will have to look for a used one.
Mike T.
Alex
Posts: 51
Joined: Thu Jun 03, 2004 7:43 pm
Location: NE PA

K-38 Mdl 14-4 sight question

Post by Alex »

Another option that I opted for years ago is to replace your S&W rear with a Millet rear sight. It has a true "target" blade (on the the Target Model) and, at least the older sight on my 14, allows for a center hold at any range. I also think it's pretty cost effective compared with other options. It's available from Brownell, Midway, and others. Note: be sure you read the selection chart correctly.

Hold center,

Alex
Tom Suswal
Posts: 10
Joined: Fri Jan 14, 2005 10:09 am

Post by Tom Suswal »

Thanks for your help. I will be looking at all the options open to me and I will let you all know how it works out.

Tom
User avatar
jackh
Posts: 802
Joined: Sat Sep 25, 2004 8:51 pm
Location: Oregon USA

Post by jackh »

what is the sight blade height presently? Measure the height from the top edge to the bottom in the windage way (groove). S&W blades are available in heights (if memory serves me) .126, .146, .160

The Weigand sight is on the high side. If you have a medium, put in the low. Or you could change or modify the front blade. Or shoot at 6 o'clock.

http://store.smith-wesson.com/store/ind ... ctiveTab=9
Post Reply