TargetTalk

I faced a similar problem when I purchased my CM84E back in 2004 With sights centered, the pistol would group app. 20-25 cm to the right at 50m distance, from the rest and free hand. Grouping the 10 was only possible with rear sight set to extreme left and front sight slightly tilted to the right, l...

I am left handed, shot a TOZ for a couple of years, late nineties. The construction of loading lever and cocking lever makes the grip asymmetrical to the left. I used the factory hand grip, which was bulky on the left side. Had to use a trigger shoe with 17mm offset to the left. Could never really t...

RCBS Little Dandy and 00-size rotor for 1.5 gr N310. (.32 S&W long)

Greetings Hans.

A bit challenging: Steyr LP5.
A piece of 1/16 strimmer wire, fed from the muzzle end, takes the bend in the magazine well.

Greetings Hans.

Edition 2013 Rule 6.7.7.1 Equipment Control Procedures: ............. It is the athlete’s responsibility that any air or CO2 cylinder is within manufacturer’s validity date (maximum of ten (10) years); this may be checked by Equipment Control and advisory recommendations may be given; ............. ...

Take out the battery, you will see a cap srew in the grip. I use the 2mm allan key as a hook to pull out the electronics.


Greetings Hans.

You may want to download a manual HERE

Greetings Hans.

My reloading data suggest a higher starting load with a lighter bullet. Maximum load hardly increases.

FWIIW: http://www.lapua.com/en/products/reload ... odata/6/35

Suggest you check with your powder/ bullet reloading data.

Greetings Hans.

I switched back to the original tube/ sight carrier. The comp model I have is the old model, as shown here: http://morini.ch/product_det.php?id=7 You may find some additional, older information here: http://ttorg.targettalk.net/viewtopic.php?p=47860 http://www.targettalk.org/viewtopic.php?t=8539 My ...

I stopped using the Morini-made compensator on my CM-84e for reason of fouling and lack of score improvement. I cannot be of much specific help, but there seems to be a special reamer for cleaning the compensator's main bores. To remove: the front sight may hide a grub screw holding the compensator....

I owned a DES69U for some 20 years. Fine build quality, accurate, very reliable, not sensitive to ammo, can't remember any jamming. After some 25000 shots there was some wear on the firing pin and the magazine lips developed hair cracks; second hand copies showed same cracks. Availability of spares ...

........ Another option could be to try and fit 5 x 3volt lithium button cells stacked in series,....... . Some years ago I tested 5 x CR2032 on a CM184E. It worked, but was not a succes; I did the standard Morini battery test, the voltage dropped to about 11 V and the pistol stopped firing. Later ...

I am living single, so my safety measures are simple. I shoot air pistol and air rifle indoors. Living room plus kitchen are good for 9.5 m. Pellet trap (louvre type) is at the the kitchen's blind wall and can be fixed at three different heights; illumination is by a low voltage 20Watt reflector spo...

I came from an Unique DES69 (company unfortunately out of business since early 2000's) and bought a new CM22M in 2004. It took some time to get used to the different rake angle, and to find out how to make the pistol reliable feeding, such as carefully stacking ammo into the magazine, and keep the m...

From the receiver 16 mm dia over a length of appr. 30 mm, tapering down to the muzzle to appr. 14 mm. Muzzle end 15 mm.


Greetings Hans.

Several years ago a shooter from India started this topic http://www.targettalk.org/viewtopic.php?t=10883&start=0&postdays=0&postorder=asc&highlight=nitrogen+air about using nitrogen in an air pistol. He reported no problems. "nitrogen" is no "air", so check for l...

I would check the manual. The pistol is maintenance-free, except for a regular smear of silicon grease on the O-ring where the air cylinder connects.

Greetings Hans.

Accessing the "competition arms database" (menu in the left) , you will find more.
Unfortunately this database was updated some 8 years ago : may/ june 2003.
No Steyr LP-2.

Greetings Hans.

On their website Steyr released a serie of service video's.
http://www.steyr-sportwaffen.at/movies/index.html

The video how to mount the new compensator can be seen here:
http://www.youtube.com/user/STEYRSportw ... J1kvZIVywE

Greetings Hans.

It is what Anschuetz says...
Manual page 33 I read: "....Please use no other means for cleaning, especially no VFG felt pellets....". (VFG stands for a make of those pellets)

Contrary to this Steyr recommends to use felt pellets in the LP2 and LP5.

Greetings Hans.