Search found 11 matches

by kayakr
Mon May 02, 2022 6:59 am
Forum: Bullseye Pistol Talk
Topic: DIY tungsten weights for Pardini?
Replies: 11
Views: 6620

Re: DIY tungsten weights for Pardini?

Ok. I did it. Cutting started slow but it went better once I found the right pressure, which is when you see sparks. You swiftly want a free disks, grinding wheel and belt sander. I did it outside with a full respirator and face mask. Deburring the cuts was harder. The fit is tighter than the steel ...
by kayakr
Tue Feb 22, 2022 1:08 pm
Forum: Bullseye Pistol Talk
Topic: gun choices for .22 target
Replies: 24
Views: 33845

Re: gun choices for .22 target

I bought a 6" sig trailside (hammerli xesse) $500 on GB, larry's sight mount $100?, ultadot on ebay$100. That would be a reasonable place to start. I upgraded to larry's trigger $80? and rink grips $200. I've been shooting with it for about 2 years and am ranked 10/90 269 avg (includes a couple...
by kayakr
Tue Feb 22, 2022 12:49 pm
Forum: SASP air pistol and sport pistol discussions
Topic: trigger pull and accuracy
Replies: 3
Views: 16508

Re: trigger pull and accuracy

Seems true for me comparing how smoothly I can trigger an AP 500g vs firearm 2lbs.
by kayakr
Tue Feb 22, 2022 12:46 pm
Forum: SASP air pistol and sport pistol discussions
Topic: special spectacles for airpistol shooters
Replies: 16
Views: 29513

Re: special spectacles for airpistol shooters

I use knobloch. I'm 55 and need glasses, astigmatism and can't focus near and far without change in glasses (I take the off them for close focus). I use a corrective lense that sets my focus just ahead of the front sight. (see shootingsight.com for test and real lenses and advice) and an iris that i...
by kayakr
Mon Feb 21, 2022 10:24 am
Forum: Bullseye Pistol Talk
Topic: DIY tungsten weights for Pardini?
Replies: 11
Views: 6620

Re: DIY tungsten weights for Pardini?

spektr wrote: Sun Feb 20, 2022 11:08 pm I dont think Id be comfy cutting tungsten with an abrasive wheel.... The dust is really hard on ya.....
Thanks for the warning. Apparently flammable as well.
by kayakr
Fri Feb 18, 2022 10:40 am
Forum: Bullseye Pistol Talk
Topic: DIY tungsten weights for Pardini?
Replies: 11
Views: 6620

Re: DIY tungsten weights for Pardini?

Rover wrote: Fri Feb 18, 2022 9:51 am Before you get too involved, why not wrap a little solder around your barrel to see if you really want/need the weights.
The weights are used dynamically. A better comparison would be removing some of the steel weights.
by kayakr
Fri Feb 18, 2022 7:38 am
Forum: Bullseye Pistol Talk
Topic: DIY tungsten weights for Pardini?
Replies: 11
Views: 6620

DIY tungsten weights for Pardini?

Anyone tried making these? I see 8mm rod online and have an abrasive cutting wheel so I’m wondering if they will fit.
by kayakr
Fri Feb 18, 2022 7:26 am
Forum: Olympic Pistol
Topic: MONTHLY AP LEAGUE FEB. 2022
Replies: 23
Views: 17541

Re: MONTHLY AP LEAGUE FEB. 2022

Peter Ashley
Av46m
Jan, Feb
530-8x
TargetScan Report Session 19.pdf
Jan
(114.54 KiB) Downloaded 122 times
546-6x
TargetScan Report Session 23.pdf
(114.45 KiB) Downloaded 137 times
by kayakr
Tue Nov 26, 2019 11:13 pm
Forum: Olympic Pistol
Topic: Improve the FAS 6004
Replies: 121
Views: 66569

Re: Improve the FAS 6004

Replaced the paper shim with an aluminum and used the square edged McMaster beech seal and still getting 320 FPS. Apparently the 1 card stock shim was sealing now. A little silicone line on the stock o ring may have also helped. The square seal is a tiny bit small and tries to squirm out but hopeful...
by kayakr
Mon Nov 25, 2019 8:00 pm
Forum: Olympic Pistol
Topic: Improve the FAS 6004
Replies: 121
Views: 66569

Re: Improve the FAS 6004

Bought a FAS 6004 used and it wasn't very powerful to begin with. Lots of torn holes. I noticed today my pellets weren't even penetrating the paper with cardboard backer. Chrono showed a bimodal distribution at 260 and 230 FPS. I went through most of the tips here and am now at 320 FPS with meisterk...